Mini-Split Warranty Registration

Please fill out all fields

You will need a copy of your installation invoice as either a jpg or a pdf, to complete this form.

Location and Contractor
System Information
Installation
Checklist
Submit

Name

Invoice Number

Owner's Name

Address *

City *

State *

ZIP *

Country *

Phone *

Email *

Technician Name

HVAC Company *

HVAC Company Address *

HVAC Company State

HVAC Company ZIP

HVAC Company Phone

HVAC Company Email

HVAC Technicians License or Certification Number *

License Approved or Certified by

Outdoor Unit Serial Number *

Indoor Unit #1 *

Indoor Unit #2

Indoor Unit #3

Indoor Unit #4

Indoor Unit #5

Indoor Unit #6

Indoor Unit #7

Indoor Unit #8

Indoor Unit #9

Installation Date *

Did you install the whole system *

Yes No

If not, what percentage of installation was done by you (HVAC Technician)

What had been done prior to your arrival?

Did you read the User Manual and Installation Instructions before you started the installation?

Yes No

Who unpacked the unit and accessory boxes to check for damage?

Voltage measured at terminal block of the Outdoor Unit *

Voltage measurement at terminal block of the

Indoor Unit A *

Indoor Unit B

Indoor Unit C

Indoor Unit D

Indoor Unit E

Wire guage, length and terminal colors between circuit breaker/ disconnect switch to outdoor unit

Wire gauge, length and terminal colors between each indoor and outdoor unit

Unit A

Unit B

Unit C

Unit D

Unit E

Size of the HVAC circuit breaker/fuse or disconnect switch to the outdoor unit.

Are the inter-connecting wires and copper lines between indoor and outdoor units installed/covered/protected by line set covers or anything else?

Yes No

What is the refrigerant pipe length between each indoor unit and the outdoor unit?

Refrigerant Pipe to Unit A *

Refrigerant Pipe to Unit B

Refrigerant Pipe to Unit C

Refrigerant Pipe to Unit D

Refrigerant Pipe to Unit E

Where are the unit(s) located?

Unit A Location *

Unit B Location

Unit C Location

Unit D Location

Unit E Location

What is the elevation difference between each indoor unit and the outdoor unit?

Elevation to Unit A *

Elevation to Unit B

Elevation to Unit C

Elevation to Unit D

Elevation to Unit E

Did you check the indoor unit for condensate leakage and refrigerant leakage, before and after connecting them? *

Yes No

Where is the outdoor unit located?

Ground Wall Balcony Roof Other

Is the outdoor unit anchored to the ground or pad, or secured onto a wall bracket? *

Yes No

Have you checked to make sure there is no cross-piping and/or cross-wiring between any two indoor units (zones)? *

Yes No

Were the refrigerant pipe ends capped or sealed, prior to running them through structures to keep debris from entering the copper lines?

Yes No

Have you checked both cooling and heating on all indoor units individually to ensure proper function? *

Yes No

Did you charge the inter-connecting copper pipes and indoor unit with nitrogen to check for positive leakage (pressures 150-200PSI), before conducting a vacuum leak check?

Yes No

Did you vacuum correctly to check the connecting pipes and indoor unit for leakage?

Yes No

What was the micron gauge reading, for how many minutes?

Did you check the compressor’s start and stop sequences to determine proper functionality? *

Yes No

Measured Refrigerant pressures at outdoor service suction valve, when unit was stabilized?

Cooling (PSI) *

Heat Pump (PSI) *

Outdoor Ambient Temp (°F) *

If copper length were not made to the supplied or recommended refrigerant pipe length, how much refrigerant added or deducted?

Temperatures

At cooling: indoor return air (°F) *

If installed when ambient temperature is too low for operation, enter NA

Cooling discharge air (°F)

Cooling and outdoor (°F)

At heating: indoor return air (°F) *

If installed when ambient temperature is too high for operation, enter NA

Heating discharge air (°F)

Heating and outdoor (°F)

Have you checked all unit functions, with the customer present, and are all functions operating correctly?

Yes No

Did you show the user how to operate the unit? *

Yes No

Did he or she understand unit operation? *

Yes No

Do you provide regular one-year free service for this installation?

Yes No

Did you list the working details in the invoice and leave a copy for the customer? *

Yes No

Installation Completed, and Unit works properly *

Yes No

Warranty Agreement

By digitally signing this document, I acknowledge the liability and responsibility for any false statement or withholding of facts. I also authorize YMGI to verify any of the details provided, and make its decision on warranty coverage. I understand that filing for the warranty DOES NOT mean automatic warranty approval. Warranties is approved only to for qualified and tested installations performed by qualified HVAC technicians. If the warranty is approved, is a standard 5 year compressor, 1 year on all other parts, and does not include labor coverage. For YMGI Certified Technicians the warranty is 7 years on the compressor and 2 years on all parts.

HVAC Technician Signature

By digitally signing this document, I acknowledge the liability and responsibility for any false statement or withholding of facts.

http://ymgigroup.com/privacy-policy/ *

Owner Signature

By digitally signing this document, I acknowledge the liability and responsibility for any false statement or withholding of facts.

http://ymgigroup.com/privacy-policy/ *